Ruwido easytip 2 manual

Please ensur e that you refer to the codes listed under the. If programming using the codes in the enclosed list failed to work then you.

Ensure that the remote contr ol is equipped with 2 new batteries see step. When using the automatic scan function for the. Press the key of your remote control for appr ox.

After seeing the 2 flashes and within 5 seconds, enter the code. After entering the code the LED will flash twice indicating that the code has. Press and hold the key until your TV switches off. Please note that this. During the automatic scanning you. If left off of the key for more than 8 seconds then the r emote will. You are very welcome to contact the manufacturer for report errors and to make suggestions for improvement.

Printed in Austria. Programming easytip Programming by Code entering 1. Switch on the device you want to use your easytip with. Turn to the TV code list other manual and look for the name of your device manufacturer. Choose your device by using the Level key image b and press the key for about 5 seconds until the LED image a blinks twice.

Enter the first 3-digit code from the list with the number keys image c on your remote control. The first figure of the 3-digit cod must be entered within 5 seconds of the LED image a blinking twice. Otherwise the LED image a will flash once and you will have to repeat the procedure from step 3. After the 3-digit code has been entered the LED image a will blink twice to indicate that the code has been accepted.

In this case, repeat the procedure from step 3. Adjusting color, contrast, bass, treble, Now point your easytip at your device and try to operate your device with your Easytip. Briefly press the Shift-key image o. Press the Level key image b. Press the chosen key within 5 seconds. The code list shows the most common codes first.

If none of the code numbers listed in the code list work properly use the Code search function. Make a note of your 3-digit code numbers. After the end of adjusting, wait for about 5 seconds until the keys get back their normal function. You can then program easytip newly. Querying the Code Numbers Code Search You will need this function to query the code found by the automatic code search, so that you can note it down in this operating manual. If none of the codes listed for your device work or if a previously entered code number no longer works or works unsatisfactorily, use the code search.

Switch on chosen device. Now enter code for query mode. Choose your device by using the Level key image b and press the key for about 5 seconds until the LED image a flashes twice. The first figure of the 3-digit code must be entered within 5 seconds of the LED image a blinking twice. Otherwise the LED image a will flash once and you will have to repeat the procedure from step 1.

Enter code code search with the number keys image c. The LED image a blinks twice. Every 1. Now press the Level key image b again until the LED image a blinks twice. This shows you that your easytip has stored the appropriate code number. Now check the function of your remote control. If your easytip does not react to the code number it has found, repeat steps 1 to 5 until you have found a optimal code number. A new code search begins with the last code number found in the previous search.

When the end of the code list is reached the LED image a will blink three times. The search is then repeated from the beginning. Please be patient. There may be many codes to search through before the code for your equipment is found. Now press key 1 image c and count the number of times the LED image a blinks. For example, if the LED image a blinks twice the first number in your code is 2.

Now press key 2 image c and count the times the times the LED image a blinks. For example, if the LED image a does not blink, the second number in your code is 0. Now press key 3 image c and count the times the LED image a blinks.

For example, if the LED image a blinks seven times, the third number in your code is 7. Your code number would therefore be If you made a mistake you can repeat the procedure any number of times. Query mode is terminated if you press any key other than 1, 2 or 3 or if you do not press any of these keys within 5 seconds.

Changing the direction or the search: It is possible, particularly in automatic search mode, to skip over the relevant code by mistake. In this case, you can reverse the direction of the search for a maximum of 5 codes by pressing the Vol-key image g. After 5 codes the search direction changes back automatically. Mit dem easytip haben Sie ein hochwertiges Produkt erworben. Sollte die Leuchtdiode Abb. Tun Sie das nicht, blinkt die Leuchtdiode Abb. Deutsch Achtung: Blinkt die Leuchtdiode Abb.

Wiederholen Sie in diesem Fall den Programmiervorgang ab Punkt 3. Testen Sie nun die Funktion Ihrer Fernbedienung. Sollte Ihr easytip auf den gefundenen Code nicht optimal reagieren, wiederholen Sie die Punkte 1—5, bis Sie eine optimal funktionierende Code-Nummer gefunden haben. Achtung: Bei erneutem Start des Suchlaufs beginnt dieser bei der Code-Nummer, die zuletzt verwendet wurde. Das Ende der Code-Liste wird durch dreimaliges Blinken angezeigt. Der Suchlauf beginnt danach wieder von vorne.

Achtung: Nach 5 Codes schaltet die Suchlaufrichtung wieder automatisch um! Notieren Sie Ihre 3-stellige Code-Nummer. VCR 2. AUX 3. Die Leuchtdiode Abb. You can then program easytip newly. If none of the codes listed for your device work or if a previously.

Choose your device by using the Level key image b and press. Enter code code search with the number keys image c. Every 1. When your easytip has found the right code your device swit-. Now press the Level key image b again until the LED. This shows you that your easytip has. Now check the function of your remote control.

If your easytip. A new code search begins with the last code number found in. When the end of the code list is reached the. LED image a will blink three times. Vorherige Seite. Fernbedienungen Ruwido easytip S7 Bedienungsanleitung 45 Seiten. Seite 3 drucken Dokument drucken 22 Seiten. Lesezeichen umbenennen. Anmelden ODER. Noch keinen Account? Registrieren Sie sich jetzt! Passwort vergessen?